If shorted, look for pinched or cut wire in oven temperature sensor circuit.Check connector terminals - Look for deformed or corrosion on terminals. What is the complete model number of the unit? Paul // Nov 27, 2014 at 12:21 pm On my ge double oven it was a simple fix. Jim // Dec 25, 2015 at 7:39 am Hi Gene: The F2 error light flashes and beeps on my 28-yr old GE JTP45 oven after it has been cleaning for about his comment is here
Rich Leave a Comment Name Mail Website Notify me of followup comments via e-mail Notify me of followup comments via e-mail. Full Answer Isolate the problemTo determine the exact cause of the F7 error code, press the Off or Clear button on the control panel, and unplug the oven. In order to provide most accurate advice I need the complete model number of the unit. Thank you!
Good luck. It also randomly cuts off during cooking. Open the door and remove the 3-4" long thin metal rod attached to the back wall.
Look for pinched wire. If you need the correct part number, the complete model number of the oven might help. All rights reserved. Ge Oven Error Code F2 F2 During CLEAN Control senses oven temperature above 915F-930F If actual over temperature condition occurred: Look for welded relay contacts.
I shut off power at fuze box. Ge Oven Error Code F7 Check Electronic Range Control (ERC) - Welded clean relay contacts. Check probe. http://www.appliancepartspros.com/repair-help/ge-fault-codes.html Ryan Bailey // Dec 12, 2015 at 11:53 am Replaced ERC on GE Profile oven model: JGB900SEF1SS Everything seemed to work like a champ for about an hour, then "F7 EA"
Thank you for the feed back. F76 Ge Oven The only way to turn it off was to flip the breaker. What is the part number of the control panel which has been replaced? Notify me of new posts by email.
The main control operates a series of software commands, which control the various features and functions of the oven. http://www.appliancehelponline.com/generalelectric.html Unfortunately this part has been discontinued and is no longer available. Ge Profile Oven Error Codes You probably can not find any information because the numbers you send are not the model number. Ge Oven F9 Error Gene // Sep 6, 2015 at 9:37 pm Hello Paula, Thank you for your question.
I did see it was flashing F2 error and honestly not sure if it turned itself off, but I know I did as soon as I saw flames. this content Gene. Look for condensation or contamination on probe receptacle. On some models before you do it, you have to remove the end caps and the bottom shield from the old control panel and install them on the new one. Ge Oven Error Code F3
Please verify the model number and resend it to me. I've seen it many times before and today I had a service call for the same problem again. If the F7 code appears after 30 seconds, it may be necessary to replace the control board. weblink Beeping stopped and ERC panel is dark.
Lee Armstrong // May 14, 2015 at 4:19 pm I changed out the control panel and now no code but it clicks and the clock flashes also nothing is working on Ge Oven Sensor Looks like the control panel/membrane assembly would need to be replaced. miguel // Dec 14, 2015 at 9:43 am Have a Ge model JGB916sek1ss F7 Error cleaning ribbon with alchol only work for few hours.
The error display just says "off". Set the time of the day and you are back in business. Gene. Ge Error Codes Washer Gene.
Q: Are electric or gas stove tops best? Look for pinched wire. One question: why did you push and hold the bake button? http://meditationpc.com/ge-oven/ge-spectra-error-f2.php You select temp and it beeps right away trying to say it reached temperature but it never even heated above room temperature.
Incapsula incident ID: 275001360017148507-35449826855553157 Request unsuccessful. Susan // Nov 5, 2016 at 8:45 am I have a ge spectra xl44 (can't find model #). I got the key unstuck and the whole thing works awesome. Thanks for your help.
This can't be normal? Gene. Look for cause - fan thermal switch not closing, fan stalled, etc. · Look for high resistance in the oven temperature sensor circuit due to high contact resistance (poor terminal crimp, Switch is normally closed and will open if area overheats due to fan not operating.
Jenn C // Oct 27, 2016 at 5:57 am Hi, our GE Electric Oven (Model jbp82s0h2ss) is giving the F2 error code and the oven is not heating/shutting off. Replace sensor if found defective. Babs Wood // Sep 18, 2015 at 6:51 pm Hi Gene, I was about 1 1/2 hours into self-cleaning my oven when the F2 light came on with the beeping noise. How do I open the door?
Is it possible for a F2 code to fix itself? I'm a mom who is prettygood with electronics and can take just about any appliance apart. I gently pried the two sandwiched membrane layers of the key pad just close to the number "3". Gene // Dec 27, 2015 at 6:31 pm Hello Jeff, Thank you for your good words.
If the door is hot, use gloves during the removal process.... F5 Loss of relay drive circuit If this fault code cannot be cancelled, replace the oven control (also called clock or ERC). Paula Albers // Sep 3, 2015 at 6:17 pm I have a GE TrueTemp Oven, it came with the house so it is most likely 2002. F2 During BAKE Control senses oven temperature above 615F-630F If actual over temperature condition occurred: Look for welded relay contacts on bake or broil relays.
F3 or F4 Open or shorted oven temperature sensor (RTD) Check sensor harness and harness connection between oven sensor and oven control. It was almost as if the top broiler turned on by itself. Gene. Something burned inside the control compartment can be due to damaged ERC.