Home > Ge Oven > Ge Profile Error F3

Ge Profile Error F3

Contents

Post the result. By Model Number By Part Description By Part Number powered by AppliancePartsPros.com #2 (permalink) 03-27-2008, 11:15 AM Mako Junior Member Join Date: Mar 2008 Posts: 12 Any Last edited by Mako : 04-02-2008 at 07:50 PM. #9 (permalink) 04-02-2008, 08:06 PM Gene Senior Expert APP Volunteer Join Date: Jul 2007 Location: Orange County, California Posts: These codes help GE Appliance Factory Service technicians quickly diagnose issues with the range or oven. weblink

Sprache: Deutsch Herkunft der Inhalte: Deutschland Eingeschränkter Modus: Aus Verlauf Hilfe Wird geladen... Once the sensor connection is accessible, set an ohm meter on the R x 10 ohm or R x 1K ohm scale and test between the two metal terminals in the Wird verarbeitet... In the event that the electronic control displays a fault code, a trained Service Technician should be called to diagnose and correct the issue.

Ge Oven Sensor

Best thanks in advance for your help. All rights reserved. If I order it, does it matter whether it is for range or oven. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden?

Transkript Das interaktive Transkript konnte nicht geladen werden. Then disconnect the sensor itself (see above) and directly measure its readings. Anmelden Transkript Statistik 3.896 Aufrufe Dieses Video gefällt dir? Ge Oven Error Codes Hinzufügen Möchtest du dieses Video später noch einmal ansehen?

Top 5 Reasons Electric Oven Temperature Is Incorrect? Ge Oven Error Code F2 Wird verarbeitet... Once the oven has fully cooled measure the sensor circuit resistance again at the control connection. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/6682-ge-error-code-f3.html You can continue asking questions for as long as you like even after you rate me.

I'll be helping you with your problem today.F3 means that your oven thinks your oven sensor is shorted. Ge Profile Oven F9 Error Why is my GE range displaying an "F3" fault code? Report This by Manage My Life December 19th, 2009 I have a GE Profile gas range model JGSP32GEV1BB. Contact an installer or electrician to correct the mis-wire and the oven will function normally.Unlock DoorThis code appears when the door will not unlock after a self clean cycle. Check the range's wiring diagram for that possibility.

Ge Oven Error Code F2

Wird geladen... It will be necessary to isolate which is the actual cause of the fault condition in order to correct it. Ge Oven Sensor Once through, the connector can be disconnected to access the sensor wire terminals to perform a resistance test of it. What Does F3 Mean On A Ge Oven Appliance411 Home The Purchase | Home Service | Repair Parts | Q&A Forum | Appliance Links News | Sponsorship and Advertising | Contact Us | Privacy Refer this Page | Support

The mounting screws can sometimes be rusted or seized in place so make sure a good screwdriver is used so the screw heads don't get stripped in the process. have a peek at these guys Top 6 Reasons Electric Oven Isn’t Self-Cleaning? Open the door and remove the 3-4" long thin metal rod attached to the back wall. Schließen Weitere Informationen View this message in English Du siehst YouTube auf Deutsch. Ge Wall Oven F3 Error Code

Top 4 Reasons Surface Element Is Not Working? let's makeExplore PublishClassesLogin|Sign Upshare what you makeFeatured:Intel IoTArduinoYarnLightingWith Instructables you can share what you make with the world, and tap into an ever-growing community of creative experts.How it Works »New Instructable If the sensor mounting screw heads are not visible from inside the oven cavity, the back panel of the range or oven may need to be removed to access the sensor http://meditationpc.com/ge-oven/ge-profile-error-f9.php A problem in the wiring harness between the control and the sensor or the electronic control itself could each result in the same error codes being displayed.

This can be caused by either a bad oven sensor or a bad display relay control board. F76 Ge Oven Password Show Threads Show Posts Register | FAQ's | New Posts | Today's Posts | Extras Go to Page... Appliance Repair Forum > Appliance Repair Help > Oven Bitte versuche es später erneut.

Melde dich bei YouTube an, damit dein Feedback gezählt wird.

If rebooting doesn’t clear the error or it comes back, you need to replace the control board.That’s the same solution they tell you for the F8 eeprom data error message. Gas Burner Sparks All The Time? Values Temperature (F/C) Resistance (ohms) 70°F / 21°C ~1080 +/-4.9 100°F / 37.7°C ~1143 +/-6.0 250°F / 121°C ~1453 +/-8.9 350°F / 176.6°C ~1654 +/-10.8 450°F / 232°C ~1852 +/-13.5 Ge Monogram Oven F9 Error Code Nächstes Video GE profile oven keypad not working easy DIY $0 fix - Dauer: 2:12 Jim's Good Stuff 4.849 Aufrufe 2:12 GE Profile Oven - Dauer: 8:01 Dan Mirabito 4.584 Aufrufe

Bitte versuche es später erneut. What does F6 represent?Assuming you didn’t hold down the keys too long, it is the error for a shorted keypad. LinkBack Thread Tools Search this Thread Display Modes #1 (permalink) 03-26-2008, 06:55 PM Mako Junior Member Join Date: Mar 2008 Posts: 12 GE error code F3 Model Number: this content After looking on the internet for this error message, I find out it is usually caused by a bad control panel.

Wird verarbeitet... I unplugged the stove waited a couple minutes plugged it back in and it still doesn't work back to the f3 error any ideas? You can reboot to see if that resolves it, or else replace sensors and wiring.What does F4 mean?That’s the error for a shorted sensor circuit. Du kannst diese Einstellung unten ändern.

I cheched the wire from the sensor plug to the control board plug and those wires are good too. I put my ohm meter probe in the backside of the sensors plug the old sensor and the new one both read the same 1. Tyler Z. You will need to use an Ohm meter to check the resistance of the temperature sensor.

disclaimer and Terms of Use. Many times, it means the keypanel needs to be replaced.F8This code usually means that the electronic control needs to be replaced.F9This code usually means that a component has failed somewhere in Double ... in wrong lock modes.

We 11/23/2016 11/23/2016 md20/20 Have a Maytag MEW6530DDB19 under counter oven that is not 11/23/2016 11/23/2016 md20/20 My microwave will not heat, magic chef mod mcd111owb at 11/23/2016 11/23/2016 md20/20 I I removed the sensor and put my meter on the sensor side of the plug and it came to the 1 for the ohms when I put it on the other Anmelden Wird geladen... If it measures approximately 1100 ohms, replace the control board.

With a multimeter, check the resistance of the sensor at room temperature and it should be about 1080 ohms.