Home > Error Code > Genmega Error Codes

Genmega Error Codes

Contents

C0045 Notes Overdispensed Check NS4 Sensor C0046 CDU Hardware Failure Error reported during CDU initialization. Use an electrical parts contact cleaner on terminals. Loose belts can slip off rollers and block sensors. 24A15 CDU detects bills prior to dispensing This means that while the ATM was initializing it detected a blocked sensor in the If persistent, it could be a defective modem. http://meditationpc.com/error-code/gle-error-codes.php

Excessive EMI emissions from outside source (neon sign, freezer)are likely causes. Before reinitializing the ATM, first the verify amount of dispensed notes in the cassette against the journal. Verify that version of Mini-Bank Software matches host processor. NOTE: Do not use metal objects to clear the jam.

D0111 Error Code

Remove any jammed paper and then reload. Remove any jammed bills from the dispenser, if no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust). C0062 3rd cassette inlet sensor not cleared Check for notes where the 3rd cassette engages the dispenser. Verify that version of ATM Software matches host processor.

Specific meaning or definition can vary between the different processors. Verify that version of ATM Software matches host processor. This can also be a problem with programming, check all programming (especially Dual Master Key setting and Host Processor Mode). 20001 Unable To Detect Cassette Remove and replace cassette - Check D2516 Atm Error Specific meaning or definition can vary between the different processors.

Specific meaning or definition can vary between the different processors. Genmega Error D2511 NOTE: it is very common to see this error in the error summary and does not usually indicate a bad or defective part. Please try the request again. D0091 Bank unavailable.

Check and reseat all belts. Genmega G2500 Manual This can also be a problem with programming, check all programming (especially Dual Master Key setting and Host Processor Mode). D00A9 ETX omitted (from configuration message). C0032 Outlet solenoid error Check and verify all connections to the dispenser circuit board.

Genmega Error D2511

D0056 No card record found Code reported by host processor (Shazam). D00A8 FS omitted (after surcharge in configuration message). D0111 Error Code Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. D2516 Error Code Remove any jammed bills from the dispenser, if no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust).

D0053 No savings account Code reported by host processor. check my blog C0059 Cash cassette 2 removed prior to dispense. Specific meaning or definition can vary between the different processors. D0098 Response type mismatch (day-close). Genmega Tech Support

Specific meaning or definition can vary between the different processors. Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. this content Remove jammed paper – Release receipt paper drawer by pressing the tab with the green sticker located at the front of the printer.

D0001 Modem initialization error Check modem in diagnostics or modem test. Hantle 1700w Error Codes Generated Thu, 24 Nov 2016 12:37:42 GMT by s_fl369 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection The primary reason for this is a bill which bounces back from the cash tray (sometimes from a customers fingers).

Check dispenser for jammed bills and reinitialize the machine.

Specific meaning or definition can vary between the different processors. In most cases you may have to remove the printer to locate difficult jams. Excessive EMI emissions from outside source (neon sign, freezer). Genmega Atm Hack Home ATM Machines Genmega Onyx Series Onyx W Series G2500 Series GT3000 Series GK1000 Bill Payment G6000 Series Hantle 1700W Series C4000 Series T4000 Series Coin Goat Series Hyosung Halo II

Replenish the cash – If using less than 75 bills, disable the “Low Cash Warning” in the Transaction Setup Menu. 20003 Reject Bin full. Reinitialize the ATM to put back in service. Check the quality of the notes and condition of the pick rollers. have a peek at these guys Verify host phone number – See D170x D2000 Phone line busy.