Home > Error Code > G3 Error Code

G3 Error Code

Contents

A. OPT2 did not end normally. ##260 [ TX/RX ] System error occurred between modem and system control board... Increase the T5 timer setting to avoid an error. Manual of the model in question. ##303 [ TX/RX ] Page memory error Cause... this contact form

Solution: Boost the transmission level so that the other party can receive the signals properly. Solution: Boost the transmission level so that the other party can receive ACK properly. Solution: Transmit to a FAX whose bits 33 and over are not defined. ##200 [ RX ] Fail to detect picture reception carrier for 5 seconds during reception. B.

Canon Fax Error Codes

Cause: BJ printer control DRAM error. Just use a cloth with isopropyl alcohol and clean this disk from both sides (by slowly moving the table in-out). B. Page 148 • Record the protocol on a DAT or MD, and have it analyzed by the local Canon office and/or Technical Center. 1.

Some people report success after installing SoundAbout to tweak the audio profiles. Page 63 Chapter 2: Service Error Codes ##005 [ TX ] In G2 transmission, GI2 cannot be received Cause Remedy • The line condition is poor, and GI2 cannot • Ask Solution: Adjust the NL equalizer so the other party can receive picture or EOP signals properly. Fax G3 A.

Cause: The home position sensor is defective. Canon Fax Error Code Ng Cause: Usually--cannot receive picture signals properly due to poor line conditions. Page 76 Chapter 2: Service Error Codes ##107 [ RX ] The transmitting machine cannot use fall- back Cause Remedy • The line condition is poor, and the signal • Ask https://archive.org/stream/printermanual-canon-g3-g4-error-code-list/canong3g4errorcodelist_djvu.txt Page 154 Chapter 2: Service Error Codes ##703 [ RX ] In CHT reception, the allowed total number of NACK re-transmissions (20 times) has been exceeded Cause Remedy • The line

Page 40 Chapter1: User Error Codes #052 [ RX ] Recording paper footer error Cause Remedy • The BJ ink has run out, causing a printer • Replace the BJ cartridge. Toshiba Fax Error Codes Cause: Image memory backup secondary battery is dead. F. Cause: Defective DES sensor.

Canon Fax Error Code Ng

Cause: STOC detected an abnormality Solution: Call NTT notifying them of the trouble E. https://www.manualslib.com/manual/457688/Canon-G3.html Page 74 Chapter 2: Service Error Codes ##104 [ TX ] RTN or PIN has been received Cause Remedy • The line condition is poor so that the other • Increase Canon Fax Error Codes A. Fax Error Codes Ricoh Cause: Defective internal unit; (+24 volts down).

Solution: Replace the board containing the Thermistor ##347 [ TX / RX ] BJ printer control ROM/ RAM check error. http://meditationpc.com/error-code/ge-error-code-f7.php D. Page 212 Chapter 2: Service Error Codes ##1053 [ TX/RX ] No connection inside the net possible [German model] Cause Remedy • Cause number #53 (No connection inside • Start a A. Canon Fax Machine Error Codes

Cause: Defective internal unit; (LBP VSREQ does not go off). By the Service Man: Changing SW03 bit 6, bit 5, and bit 4 of service soft switch #1 SSSW will affect all settings, i.e., all transmissions will be long distance transmissions: Page 66 [ RX ] In G2 reception, a signal other than PIS or GC2 is received after transmission of MCF2 or GI2 Cause Remedy • The procedure signal has a http://meditationpc.com/error-code/ge-f3-error-code.php Page 39 Chapter1: User Error Codes #050 [ TX ] Cipher transmission cannot be used [NTT model] Cause Remedy • The other party is not equipped with a ci- • Transmit

Cause: Defective internal unit. Canon Super G3 Troubleshooting Use direct transmission. #024 [ TX ] Delayed transmission fails Cause Remedy • For combination of delayed transmission with direct transmission, no document is set at the specified time. • Once received correctly. ##803 [ TX/RX ] Phase error occurred when a status signal was being received from the hard disk Cause...

Solution: Set the document and have the other party call again F.

Solution: Refer to Service manual ##331 [ TX / RX ] The remaining amount of Ink in the BJ cartridge cannot be detected. Page 149 • Record the protocol on a DAT or MD, and have it analyzed by the local Canon office and/or Technical Center. 1. Solution: Adjust the echo monitor time after CFR transmission so picture signals can be received properly. Canon Fax Error #099 Page 204 Chapter 2: Service Error Codes ##1028 [ TX/RX ] Invalid number format (Address incomplete) Cause Remedy • Cause number #28 (Invalid number format • Check the telephone number of

Solution: Lower the transmission start speed to 4800 bps. Page 10 Introduction Password Used When Making Settings: A password may also be used for confidential mailboxes, memory lock Rx, call restriction, and other functions. The line will be disconnected if no significant signal is received during the period. 5.T1 Timer: No. 11 of Service Soft Switch #3 NUMERIC param. his comment is here A.

B. Solution: Adjust the NL equalizer so that the other party can receive the picture or EOL signals properly. Solution: Replace the PC board containing the BJ controller. Cause: Carriage movement prevented by one of the following: damaged shaft, deformed parts, insufficient grease, dirty sliding part of the pressure plate, or foreign material in the carriage.

Cause: The other party cannot receive picture signals properly due to poor line conditions. quiry) arrived from the network. • Print out a communications analysis list, and analyze it. Solution: Have the other party boost their transmission level so they can receive the phase signal properly. B.

Make sure you have the latest LG drivers installed on your PC. A. Solution: Boost the transmission level so the other party can receive picture or EOM signals properly. A.

B. A. Solution: Boost the transmission level so the other party can receive properly. Solution: Power cycle the machine (unplug unit).

Cause Remedy 1-34... D. Page 107 Chapter 2: Service Error Codes ##285 [ TX ] DCN has been received after transmitting Cause Remedy • The Stop button was pressed during a com- • Transmit once NOTE: This code is not in the G3 book even though several manuals indicates it is. ##672 [TX] The protocol did not move from phase 2 to phase 3 and

Page 203 Chapter 2: Service Error Codes ##1026 [ TX/RX ] Non-selected user clearing Cause Remedy • Cause number #26 (Non-selected user • Start a communication once again. A. Solution: Replace the SCNT PWB. ##338 [ RX ] Printing position correction failed. B.